全國咨詢熱線
不銹鋼切丁機主要適用于肉類脫水蔬菜速凍蔬菜加工廠及食品醬菜行業加工各種根莖類蔬菜成正方體及長方體形狀，其原理在于撥盤帶動被切物體高速旋轉，利用物體離心力，借助立刀將被切物體切成片狀，然后經過圓盤切絲刀切成條狀，并將被切物料送入橫切斷刀口，由橫切斷刀切成所需要的立方體或長方體切丁機工作一行程后，料倉存料約一到二毫米，刀片間隙小于10絲（0.1毫米）。
Stainless steel Dicer is mainly used in meat dehydrated vegetable quick frozen vegetable processing factory and food and pickle industry to process all kinds of root vegetables into cube and cuboid shape. Its principle is that the dial drives the object to rotate at a high speed, uses the centrifugal force of the object, with the help of the vertical knife to cut the object into slices, and then cuts into strips through the disc cutter, and sends the cut material to the horizontal cutting The cutting edge is cut into cubes or cuboids by the cross cutting cutter. After one stroke, the material in the bin is about 1 to 2 mm, and the blade gap is less than 10 wires (0.1 mm).
為了保證不銹鋼切丁機使用的穩定性以及性，在操作不銹鋼切丁機之前，使用者應做好必要的檢查工作，其中：
In order to ensure the stability and efficiency of the stainless steel cutting machine, the user should do the necessary inspection before operating the stainless steel cutting machine
仔細檢查切丁機是否存在缺損松問題，確保機器處于完好狀態。
Carefully check the cutter for any defects and looseness to ensure that the machine is in good condition.
檢查殼體內是否有異物存在，將殼體內異物掉，否則容易引起刀片的損壞。
Check whether there is any foreign matter in the shell, and remove the foreign matter in the shell, otherwise it is easy to cause damage to the blade.
清理操作場地，檢查電源電壓是否與本機使用電壓相符，接地 標志處是否可靠連接地線。合上開關按下“開”按鈕，檢查轉向是否正確（面對推料撥盤，推料撥盤逆時針方向旋轉為正確），否則，切斷電源調整接線。
Clean the operation site, check whether the power supply voltage is consistent with the use voltage of the machine, and whether the ground wire is reliably connected at the grounding mark. Close the switch and press the "on" button to check whether the steering direction is correct (in the face of the pusher dial, the pusher dial rotates counterclockwise to be correct). Otherwise, cut off the power supply and adjust the wiring.
接通水源，以備使用。
Connect the water source for use.
在不銹鋼切丁機的使用中，使用者應注意以下幾點要求：
In the use of stainless steel cutting machine, the user should pay attention to the following requirements:
，應將被切物料洗凈去雜，如果被切物料混有沙石與泥塊，刀刃口與刀板容易損壞和磨鈍。物料zui大切割直徑應不超過100mm，如果大于此直徑須分塊。
First of all, the materials to be cut should be cleaned to remove impurities. If the materials to be cut are mixed with sand and mud, the blade and blade are easy to be damaged and blunt. The large cutting diameter of material Zui shall not exceed 100mm. If it is larger than this diameter, it shall be divided into blocks.
按下啟動按鈕電機運轉。（如上蓋未壓合在機架上，不能壓合開關XK，線路不通，電機不能運轉）
Press the start button to run the motor. (the upper cover is not pressed on the rack, the switch XK cannot be pressed, the line is blocked, and the motor cannot operate.)
將被切物料從料斗均勻連續投入進料斗中，在推料撥盤的作用下，被切片刀切割成所要求的厚度接著被圓盤切絲刀切成條狀，zui后被橫切斷刀切成方塊。
The cut material is uniformly and continuously put into the feed hopper from the hopper. Under the action of the pushing dial, it is cut to the required thickness by the slicing knife, then cut into strips by the disc cutter, and then cut into squares by the cross cutter after Zui.
切丁機規格的調整：是通過調整切片厚度，更換圓盤切絲刀和橫切斷刀來改變的。
Specification adjustment of the Dicer: it is changed by adjusting slice thickness, replacing disc cutter and cross cutter.
機器工作時，切勿將手及其他異物放入殼體中，以免發生危險。
When the machine is working, do not put hands and other foreign matters into the shell to avoid danger.
本文來自：切丁切塊機更多的內容請點擊：http://avcrowdlimeera.com我們將會為您提問的問題提供一個滿意的服務，歡迎您的來電！
This article comes from: Dicer more content please click: http://avcrowdlimeera.com we will provide a satisfactory service for your questions, welcome your call!
