談?wù)勱P(guān)于切片機各個位置的潤滑和保養
發布時間：2020-09-07
來源：http://avcrowdlimeera.com
發布人：admin
現在市面上各式各樣的機械設備變得越來越多，這其中也不乏一些精度高的機械設備，它們的出現是科技進步的印證，切片機是現在常見的一種設備，在使用它的時候要按時對其進行潤滑。
Now there are more and more kinds of machinery and equipment on the market. There are also some high-precision mechanical equipment. Their appearance is the confirmation of scientific and technological progress. Slicer is a common equipment now. When using it, it should be lubricated on time.
切片機中需要潤滑的部位有不少，采用的潤滑介質也是有區別的，比如說它的離合器、彈簧、鏈輪張緊裝置、往返運動部位導軸、開合機構等部位的潤滑加黃油。
There are many parts in the slicer that need to be lubricated, and the lubricating media used are also different. For example, the lubrication of clutch, spring, sprocket tensioning device, guide shaft of reciprocating motion part, opening and closing mechanism, etc.
而切片機中的位塊凸輪裝置、主傳動室潤滑要加機油，且半年換1次機油，由視窗油的清澈程度決定；角度分割器潤滑每半年1次；空壓機潤滑，三個月加1次。
The lubricating oil should be added to the position block cam device and main transmission chamber of the slicer, and the oil should be changed every half a year, which is determined by the clarity of the window oil; the angle divider should be lubricated once every half a year; the air compressor should be lubricated once every three months.
除了潤滑之外，在使用它的時候，還要留意防塵和清潔、電氣方面的故障。除了這些以外，它的換油也是很重要的，要保障平臺的四角度與上凈平臺之間的間隔，只有保持正確的間隔，才能使機器正常的運轉。
In addition to lubrication, in the use of it, but also pay attention to dust and cleaning, electrical failure. In addition to these, its oil change is also very important. To ensure the spacing between the four angles of the platform and the upper clean platform, only by maintaining the correct interval can the machine run normally.
在切片機切片時，還要注意不要將大量的廢紙邊、紙毛弄進鏈條傳動部位、模切部動平臺及一些其它的旋轉部位，以免造成運轉故障，損害切片機，如果在日常使用它的時候不能較好的保養機器，不但會額外的增加維修機器的開支，對機器的損害也很大。
When slicing the slicer, pay attention not to put a lot of waste paper edge and paper wool into the chain drive part, die cutting part moving platform and some other rotating parts, so as to avoid running failure and damage to the slicer. If the machine can not be maintained well in daily use, it will not only increase the cost of repairing the machine, but also cause great damage to the machine.
